Join Shelby Forums Today

69 Console wiring question

Discussion in '1965-1970 Shelby Mustang GT350 & GT500' started by robbob36, Jan 11, 2012.

  1. Jan 11, 2012 #1
    robbob36

    robbob36 Member

    Posts:
    18
    Likes Received:
    0
    Joined:
    Dec 7, 2011
    Location:
    Texas
    Hey guys
    On the harness that goes to the console switches and guages there are 2 black connectors they both have 2 wires one wire is black and the other is blue with what looks like a stripe on it. The wires are the same on both connectors. What do these connectors go to? Thanks Rob:doh:
     
    robbob36, Jan 11, 2012
    robbob36, Jan 11, 2012
    #1
  2. Jan 13, 2012 #2
    Coralsnake

    Coralsnake Well-Known Member

    Age:
    60
    Posts:
    1,048
    Likes Received:
    16
    Joined:
    Sep 8, 2004
    Location:
    The Northcoast
    Can you post a picture?
     
    Coralsnake, Jan 13, 2012
    Coralsnake, Jan 13, 2012
    #2
  3. Jan 13, 2012 #3
    robbob36

    robbob36 Member

    Posts:
    18
    Likes Received:
    0
    Joined:
    Dec 7, 2011
    Location:
    Texas
    I will try to take one when I get home tonight Thanks Rob
     
    robbob36, Jan 13, 2012
    robbob36, Jan 13, 2012
    #3
  4. Jan 16, 2012 #4
    per

    per Active Member

    Age:
    70
    Posts:
    25
    Likes Received:
    0
    Joined:
    Jan 30, 2007
    Location:
    europa
    hi buy a wiring schema from NPD.Take the 70 mustang mach1 ,the
    last two pages is special for shelby.

    per
     
    per, Jan 16, 2012
    per, Jan 16, 2012
    #4
  5. Jan 16, 2012 #5
    robbob36

    robbob36 Member

    Posts:
    18
    Likes Received:
    0
    Joined:
    Dec 7, 2011
    Location:
    Texas
    Thanks for the tip. I have the original wiring diagram from Ford that is in the shelby shop manual supliment, is the one from NPD the same? The original Ford one is hard to understand. Thanks Rob:thumbsup:
     
    robbob36, Jan 16, 2012
    robbob36, Jan 16, 2012
    #5
  6. Jan 19, 2012 #6
    Doug D

    Doug D Active Member

    Posts:
    38
    Likes Received:
    1
    Joined:
    Jul 29, 2010
    Location:
    Washington State
    It so happens the the '69 I'm working on has the console partially removed so maybe this will help.....

    Under the ashtray is a 2-pin connector for the ashtray light. It has a grey/red wire and a black wire.

    The wires go forward to another 2-pin connector located roughly under the two gauges. At that connector the grey/red changes to blue/purple and the single black wire turns into two black wires.

    I don't see any other 2-pin connectors. Is this what you're after? If not, shout back and I can look again. Elsewhere in the wiring are two 4-pin connectors and one 1-pin connector. These branch off to the right of the radio area, under the dash. Some of the wiring branches off to the left of the radio area with some other connectors under the dash...but I don't think that's what you're talking about.

    Cheers
    DD
     
    Doug D, Jan 19, 2012
    Doug D, Jan 19, 2012
    #6
  7. Jan 25, 2012 #7
    robbob36

    robbob36 Member

    Posts:
    18
    Likes Received:
    0
    Joined:
    Dec 7, 2011
    Location:
    Texas
    Thanks the help that makes sense. I have been buried the last few weeks and have not had time to remove my console top to check it out and take a picture. Thanks Rob
     
    robbob36, Jan 25, 2012
    robbob36, Jan 25, 2012
    #7

Share This Page